Welcome to the Wild-About-Trapping.com Forums

Friends, Family and Outdoor Traditions
It is currently 19 Nov 2017, 09:02

All times are UTC - 6 hours [ DST ]





Post new topic This topic is locked, you cannot edit posts or make further replies.  [ 1 post ] 
Author Message
PostPosted: 21 Dec 2012, 14:22 
Offline
KING OF THE POSTERS
KING OF THE POSTERS
User avatar

Joined: 03 Feb 2008, 12:18
Posts: 16404
Location: Lufkin, TX
http://i872.photobucket.com/albums/ab28 ... dd3380.jpg
When i first put the beaver on the board i put one nail at nose end and one at tail end. Then i pull the center out towards the ring and put a nail in then do the other side After that i put nails by the leg area and pull out to line. You now have 8 nails to begin. By doing this you can tell if you are going to be to tight or to loose.

http://i872.photobucket.com/albums/ab28 ... 926cc6.jpg
next i clean all the edges of the beaver, don,t worry from the last nail to head or last nail to rump. That will clean up later.

http://i872.photobucket.com/albums/ab28 ... 0e81b8.jpg
sides are clean

http://i872.photobucket.com/albums/ab28 ... b07f52.jpg
now i start from the center of the beaver and work my way up to head area

http://i872.photobucket.com/albums/ab28 ... 8d95d9.jpg
after reaching the front leg area i then do the back section as far as the hind legs.

http://i872.photobucket.com/albums/ab28 ... 5f4f6e.jpg
Now we do the head first. Better to head first because the shoulder area can get a bit tight if you do the bottom end first. Put a nail in each lip and pull tight and nail, you will be well over the ring size you are using. Now you can see that the head is puffed up with loose hide.

http://i872.photobucket.com/albums/ab28 ... c2c8a9.jpg
take a knife and slit the nose, this will give you more shoulder slack and also will allow you to pull the hide tight on head area.

http://i872.photobucket.com/albums/ab28 ... 41dfd5.jpg
now put a nail in nose section and pull it out tight.


http://i872.photobucket.com/albums/ab28 ... 017637.jpg
now your head area is tight to remove the ears and clean up around the head area. Many trappers always have a hard time around the head. This makes things a whole lot easier.


http://i872.photobucket.com/albums/ab28 ... 23e38a.jpg

http://i872.photobucket.com/albums/ab28 ... 1c678d.jpg

http://i872.photobucket.com/albums/ab28 ... 02879b.jpg
now that you got your head area clean enough you can carry on with nailing the beaver from the front legs up to the nose area.


http://i872.photobucket.com/albums/ab28 ... 3fd892.jpg
now start to remove the excess from head area.

http://i872.photobucket.com/albums/ab28 ... c72cf5.jpg


http://i872.photobucket.com/albums/ab28 ... f1cff1.jpg
head should look this

http://i872.photobucket.com/albums/ab28 ... e9c3f3.jpg
now we go to the back end and do the same method we did at the front. Use 2 nails and pull the sides down oast your line, then remove your center tail nail and pull the hide down farther.

http://i872.photobucket.com/albums/ab28 ... ea2b01.jpg
now that your tail section is snug you can easly clean up around your back leg holes

http://i872.photobucket.com/albums/ab28 ... b84e40.jpg
after you have cleaned up the tail section nail as shown.

http://i872.photobucket.com/albums/ab28 ... 4f683e.jpg
remove the excess fat and grizzel

http://i872.photobucket.com/albums/ab28 ... 92a75e.jpg
now you can cut some off your leg hole openings, just a trim which will get rid of some of the fat.

http://i872.photobucket.com/albums/ab28 ... e23be2.jpg

http://i872.photobucket.com/albums/ab28 ... 8232d3.jpg

http://i872.photobucket.com/albums/ab28 ... 74168b.jpg
closing the leg holds, i use 3 nails overlapping on back legs and 2 over lappiing on front legs

http://i872.photobucket.com/albums/ab28 ... a6ce22.jpg

http://i872.photobucket.com/albums/ab28 ... 295b12.jpg

http://i872.photobucket.com/albums/ab28 ... bb3369.jpg

http://i872.photobucket.com/albums/ab28 ... 7c0405.jpg
i lift the pelt off the board just high enough so my fingers slide under. There is no need to go right to the top of your nail.

http://i872.photobucket.com/albums/ab28 ... fda8bc.jpg
there you have it a finished beaver. My nail spacing is about 3/4 to inch maybe just over. Keep your nails spacing close to the same and you will have a more nicer shape to the beaver instead of a scallop look. Any questions just send me a pm.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic This topic is locked, you cannot edit posts or make further replies.  [ 1 post ] 

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  


Powered by phpBB® Forum Software © phpBB Group